Search:

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    842
    Views
    151,729

    Chrysler rear jamb switches are located 1/2"...

    Chrysler rear jamb switches are located 1/2" inside the door seal about even with the bottom of the upper hinge. There's a dimple in my Volare wagon's B-pillar there, with no switch.
  2. Replies
    842
    Views
    151,729

    DORMAN 84803 Replace with new. RockAuto.com has...

    DORMAN 84803 Replace with new. RockAuto.com has them.
  3. Replies
    842
    Views
    151,729

    Unless you would have some type of very old unit...

    Unless you would have some type of very old unit or naturally a lockup unit the shafts should all be the same as far as the hundreds I have done.
  4. Replies
    406
    Views
    42,519

    I have (had) a pretty strong Fb presence. And...

    I have (had) a pretty strong Fb presence. And it's incredibly useful to helping others with their Mopars and also selling parts. You can only do without social media if you're content to just do your...
  5. Replies
    219
    Views
    61,364

    Sticky: Man, I will just pull our babies outside and set...

    Man, I will just pull our babies outside and set em in the yard together for a few hours all the time even if we aren't going anywhere. Sometimes we show off and line em up out front, but other times...
  6. Replies
    664
    Views
    157,132

    You can get the 6.4/392 intake to work on a 5.7,...

    You can get the 6.4/392 intake to work on a 5.7, but you will need the adapter plates. It will not directly bolt onto a 5.7 Gen III HEMI.
  7. Replies
    13
    Views
    3,276

    A butt weld would work but, it'd be better if the...

    A butt weld would work but, it'd be better if the flange was over the outside of the pipe. My idea would be enlarge the holes in the flanges slightly so the pipe is a tight slip fit and then weld.
  8. Replies
    842
    Views
    151,729

    If you are worried about leaks then use Remflex...

    If you are worried about leaks then use Remflex gaskets. They won`t leak but the downside for me was they stuck to the head and they got torn when removing. Many years ago hooker was the header most...
  9. Replies
    842
    Views
    151,729

    Well, Dorman..........That's code for Made in...

    Well, Dorman..........That's code for Made in China (cheaply and with not much quality control in most cases). There are good vacuum caps out there. Not sure what store might carry them though. At...
  10. Replies
    842
    Views
    151,729

    https://www.flashpowerparts.com/billet-parts-for-c...

    https://www.flashpowerparts.com/billet-parts-for-chevy-gm-engines/64-billet-thermostat-housings-water-neck-chrysler-mopar-hemi-0-degree.html
  11. Replies
    842
    Views
    151,729

    It took a bunch of looking but I finally found...

    It took a bunch of looking but I finally found the service manual section that explains the operation of the electric choke. They hid it towards the end of the "EMISSION CONTROL" section.

    The...
  12. Replies
    842
    Views
    151,729

    Just in case you need any more info or have not...

    Just in case you need any more info or have not checked RockAuto for a new ignition switch they list two that fit with a flat connector. WVE/AIRTEX/WELLS 1S6141 and STANDARD MOTOR PRODUCTS US88
  13. Replies
    842
    Views
    151,729

    chaz, of the top of my head it should be 3755770...

    chaz, of the top of my head it should be 3755770 IIRC. There are some on ebay. I may have a used one.
  14. Replies
    842
    Views
    151,729

    You should be able o rotate the counter weight on...

    You should be able o rotate the counter weight on the right side exhaust manifold and then, it should come back on it's own with spring tension. They seize up more often than not unless they have...
  15. Replies
    842
    Views
    151,729

    Yes the egr does get the exhaust from the cross...

    Yes the egr does get the exhaust from the cross over but that is just a start. It is impossible to see all the carbon buildup through that port. A pile of carbon that can be cleaned out would...
  16. Replies
    842
    Views
    151,729

    For paint runs you can either use a paint run...

    For paint runs you can either use a paint run razor and blockers to shave it down, then wet sand, finishing with 2,000 grit or finer followed by buffing or carefully wet sand the run out and then...
  17. pic

    pic
  18. here is a pic of my 77 2dr with 5 leaf springs...

    here is a pic of my 77 2dr with 5 leaf springs drivers side
  19. here is a chart I found online...

    here is a chart I found online https://sep.yimg.com/ay/chucker54/chrysler-leaf-spring-dimensions-16.gif
  20. I looked in my mitchell book and it shows no...

    I looked in my mitchell book and it shows no difference between 2 and 4 dr springs. The only difference shown is whether they are 4 or 5 leaf springs. 5 leaf usually is station wagon and HD...
  21. My guess is they used a spring from a different...

    My guess is they used a spring from a different car (maybe e body or something) because it was available instead of having the correct spring made up. The new hanger being it has the two holes (i...
  22. Replies
    4
    Views
    2,083

    "Why not?" Careful, that's how my car turned into...

    "Why not?" Careful, that's how my car turned into a 12 year project! lol

    Not a slant 6 but an idea for the tailpipes. I built them myself but a custom exhaust shop could bend them if you don't...
  23. Thread: Door latch

    by 77rr2x4s
    Replies
    15
    Views
    4,504

    front and rear door latch are a different part...

    front and rear door latch are a different part number. two door and four door front driver door latch shows the same part number 4310529. 76-80 f body same number, also same as 80-81 Lebaron, 77-84...
  24. Thread: Door latch

    by 77rr2x4s
    Replies
    15
    Views
    4,504

    yes it is the same as other years/ models but I...

    yes it is the same as other years/ models but I would have to check part numbers to be sure exactly which ones. I`m pretty sure the back door latch is different. I will check part numbers tomorrow.
  25. Replies
    17
    Views
    5,560

    Yes, this is a good part. I have bought this part...

    Yes, this is a good part. I have bought this part from them. The only issue I had was with the locking ring that came with it. It didn't seal well. I reused the original locking ring and everything...
Results 1 to 25 of 29
Page 1 of 2 1 2